Please turn the wheel on the back until you obtain a clear connection signal.

A set-up card can be found in the packaging with individual settings for the most common telephones.

{gnresource:HSS_GN9120-EinstellungRad-WG}

Requirements:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}

GN 9120 -xx-11

{gnresource:HSS_logo_t_com}


{gnresource:HSS_ComfortPro_P100_Klein}

Comfort pro P 100 /300 /500

Connection:

1) Plug one end of the DHSG-cable marked into blue in the
"Headset icon" jack of the telephone.

2) Plug the split end of the DHSG-cable in the base station of the GN 9120. Plug the RJ10 connector into the jack marked with the "telephone icon" and RJ45 connector into the jack marked "AUX" on the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set to DHSGsoftware.
(The GN9120 EHS is always supplied in the DHSG mode. )

To check the set software proceed as follows:

Plug the headset into the base station and press the PLUS and MINUS
buttons for 6 seconds simultaneously till the Online-indicator begins to blink on the headset.

Now your actual software is shown to you.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp is for RHL"; the MUTE-LED for "DHSG" the accu-indicator is for " AEI.

With thePLUSand MINUS buttons you can now switch between the individual software types.
To confirm the set software, the base station automatically changes after 10 seconds again into the charge status.

Base setting:

Set the telephone-set-up switch (A-G) to "A"

{gnresource:HSS_9120_basis_einstellung_klein}

Seting transmission volume:

Try calling someone with your headset.
Now press the PLUS and MINUS buttons simultaneously on the headset, following which you will immediately hear a signal tone.

{gnresource:HSS_GN9120-�bertragungslautstärkeeinstellen-WG}

Now you can increase the microphone volume with PLUS or decrease it with MINUS. As confirmation you will hear a gentle signal tone in the headset after 5 seconds. Then the settings will be stored automatically.

Setting telephone:

In addition a headset button must be set on Comfort Pro.

Enable Menu > Entire menu > Telephone settings > Headset

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111

{gnresource:HSS_Detewe_logo}

{gnresource:HSS_Aastra_70_IP}

Open Phone 71 / 73 / 75

Open Phone 73IP / 75IP

Connection:

1) Plug in the end of the DHSG cable that is marked in blue on 1 side to the socket of your telephone which is marked with a"Headset symbol"

2) Plug in the split end of the DHSG cable to the basestation of the GN 9120. Plug the RJ10 plug into the socket with the complete "Telephone symbol" and the RJ45 plug into the socket marked with "AUX" to the GN 9120 Base station.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

 The GN 9120 must be set forDHSG Software .
(the GN 9120 DHSG is always provided in DHSG Mode)

For control, Checking and setting can be carried out as follows:
Plug the headset into the basestation.

Then press the PLUS and MINUS button simultaneously for 6 seconds until the Online display on the headset starts to flash.

Now the current software is displayed on the basestation.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp displays "RHL"; the MUTE-Lamp for"DHSG" the accumulator display "AEI".
With the help of PLUS or MINUS button you can toggle between particular kinds of software.

Base installation:

The adjuster (small wheel) on the basestation must be set to "A" .

{gnresource:HSS_9120_basis_einstellung_klein}


Adjusting the transmission volume:

Please make a call using the headset .

Now you must press the PLUS and MINUS button on the headset simultaneously, immediately after which a beep is heard.

Now you can increase the volume with the aid of the PLUS button or decrease it with the aid of the MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a mild beep that rings after about 10sec . The settings are subsequently automatically saved.

Telephone installation:

Open Phone 71 Menu > Settings > Audio > Headset ON                                

Open Phone 73 / 75 incl. IP:  Menu > Overall menu > Telephone setting > Headset ON                                             

     ------->       

Please first check the base PIN code of your SL1/SL100 // T-Sinus 701/711 DECT telephone. This must be set to 0000 so that it corresponds to the preset PIN code of the GN 9120 DG.

Please press the >MENU button on you cell phone, then >Set base >System PIN

 

The base PIN code can now be changed if it is not already set on 0000.

Notice: The authentication code 0000 is already standard with many DECT telephones, therefore changing the code is probably unnecessary.

Now headset pairing can begin:

Switch the GN 9120 DG into register mode. Hold the three function buttons on the headset pressed down for 6 seconds until the online display on the headset begins to blink rapidly.

Now, hold the Paging button (silver button on the DECT telephone base) pressed down until the online display on the headset begins to blink. This process requires approx. 5 seconds and afterwards the headset is registered in the DECT base.

When you press the INT button on the telephone, you will now find an additional second INTernal line:

  >  

INT 1 = Mobile telephone SL1/SL100 or T-Sinus 701/711

INT 2 = GN9120DG

The headset now rings automatically when the cell phone is called. You can answer this call and end it again with the multifunction button on the headset, or you can answer it normally on the DECT telephone and possibly connect it to the headset later.

The call can also be transferred from the cell phone to the headset with the INT button. For this, press the INT button during the call and select INT 2. Your GN9120DG will now ring and you can answer the call there with the multifunction button.

In order to make a call with the headset, you must first dial the number on the telephone and then connect the call to the headset, since you can not dial directly on the headset.

 

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111


{gnresource:HSS_Aastra_logo}

{gnresource:HSS_Aastra_70_IP}

Office 70 IP
Office 80 IP


Connection:

1) Plug the 1-sided end of the DHSG cable that is marked in blue into the socket of your telephone which is marked with a"Headset symbol"

2) Plug the split end of the DHSG cable into the basestation of the GN 9120. The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked with "AUX" to the GN 9120 basestation.

{gnresource:HSS_9120EHS_DHSG}


Software setting:

 The GN 9120 must be set to the DHSG Software .
(the GN 9120 DHSG is always supplied in DHSG Mode)

For control, checking and setting can be done as follows:
Plug the headset into the basestation.

Then press the PLUS and MINUS button simultaneously for 6 seconds until the online display on the headset starts to flash.

Now your current software is displayed at the basestation.

The radio lamp displays "RHL"; the MUTE-Lamp "DHSG" and the Accumulator-display represents "AEI".
{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

With the help of the PLUS or MINUS button you can toggle between different kinds of software.
Installation of the software is confirmed when after about 10 seconds the device automatically changes over to the charge condition
.


Base setting:

The adapter (small wheel) on the basestation must be positioned to "A".

{gnresource:HSS_9120_basis_einstellung_klein}


Adjustment of the transmission volume:

please make a call using the headset Now press both the PLUS and MINUS button simultaneously on the headset and immediately a beep is heard.

Now by using the PLUS button the microphone volume can be increased or alternatively decreased by using the MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a slight beep heard after about 10 seconds. All the settings are subsequently automatically saved.


Telephone setting:

Menu > Settings > Audio > Headset ON

Requirements:

Jabra GN9120 Standard

Art.no.: 9120-xx-01{gnresource:HSS_GN9120-Bild-WG}

Jabra GN8110 USB Adapter            +        Jabra GN cable end piece 8800-00-01

{gnresource:HSS_GNUSB-AdapterBild-WG}                  {gnresource:HSS_GN8800-00-01Bild-WG}

Desktop PC or laptop with one of the following system programs:

WINDOWS 98/SE

WINDOWS 2000/ME

WINDOWS XP

Macintosh OS 9.0.4 (or higher)

Suse Linux from kernel 9.0

 

Connection:

1. Connect the Jabra GN cable end piece to the GN8110 USB adapter quick decoupler (QD plug).

2. Insert the 4-pin RJ10 modular connector into the socket on the Jabra GN9120 base station labeled with a telephone symbol.

{gnresource:HSS_GN9120BasisQuer-ohneKabel-WG}(internal socket/telephone symbol)

3. Insert the Jabra GN8110 USB plug into a free USB port on your PC.

 

Setting the audio and playback volume on a desktop PC or laptop:

The audio and playback volume should be set to halfway in the system settings under Sounds and Audio Device when connecting the GN9120 via a USB adapter.

{gnresource:HSS_VolumeControl-USB-WG}

 

Setting the transmission volume on the Jabra GN9120:

Please call someone with the headset on.

Now press the PLUS and MINUS button on the headset simultaneously, a signal tone will then sound.

You can now increase the microphone volume by pressing PLUS or lower it by pressing MINUS.

After 15 seconds, a faint signal tone can be heard in the background confirming the change. The settings are then automatically saved.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

 

 Adjustment on the GN9120 base station:

The adjustment control (small wheel) on the base station must be set to "A".

{gnresource:HSS_GN9120-EinstellungRad-WG}

Check the battery is correctly fitted inside the headset, and/or the headset is placed correctly in the
base.

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111

{gnresource:HSS_logo_t_com}


{gnresource:HSS_ComfortPro_P500_IP_Klein}

Comfort P 300/500 IP

Connection:

1.) Plug the 1-sided end of the DHSG cable that is marked in blue into the socket of your telephone marked with the " Headsetsymbol " .

2) Plug the split end of the DHSG-cable into the base station of GN 9120. The RJ10 plug is plugged into the socket with the complete " Telephone symbol " and the RJ45 is plugged into the socket marked with " AUX "at the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set for DHSG Software .
( The GN 9120 EHS is always delivered in DHSG Mode. )

For checking the installed software, proceed as follows:

Plug the headset into the basestation and press the PLUS and MINUS button simultaneously
for about 6 seconds until the online display on the headset starts to flash.

Now your current software is displayed at the base station.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp represents RHL; the MUTE-LED DHSG and the accumulator display represents AEI.

With the aid of PLUS and MINUS button now you can toggle between different kinds of software.
Installation of the software is confirmed when the base station automatically changes over to the charge condition again after about 10 seconds.

Base setting:

Set the telephone setup switch ( A-G ) at "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the transmission volume:

With the headset please make a call.

Now both PLUS and MINUS button on the headset must be pressed simultaneously and immediately a beep is heard.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now by using the PLUS button the volume of the microphone can be increased or alternatively reduced by using the MINUS button.
This is confirmed by a slight beep heard in the headset after about 5 seconds. The settings are subsequently automatically saved.

Telephone installation:

Additionally a headset button must be installed at the Comfort Pro .

Menu > Overall menu > Telephone settings > activate headset .

With the Hall setting, the microphone volume has to be turned down.

Please call someone with the headset on.

Now press the PLUS and MINUS button on the headset simultaneously, a signal tone will then sound.

You can now increase the microphone volume by pressing PLUS or lower it by pressing MINUS.

After 15 seconds, a faint signal tone can be heard in the background confirming the change. The settings are then automatically saved.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

To register the GN 9120 DG on your DECT telephone, first read the instructions on how to register a new mobile device in the manual supplied with your telephone.

Please check the system authentication code for your DECT telephone. This needs to be set to 0000 so that it corresponds to the preset PIN code of the GN 9120 DG.

{gnresource:HSS_Siemens-SL74-WG}Note: The authentication code 0000 is already standard with many DECT telephones so you probably do not need to change the code.

{gnresource:HSS_9120_GAP-Anmeldung-WG}Switch the GN 9120 DG to register mode. Please hold the 3 function buttons on the headset for 6 seconds until the online display on the headset starts to flash quickly.

The base station can now search for the headset (for this, please follow the individual steps in the DECT telephone manual).

• Check that the mute function is off.
• Check the position of the boom arm and make sure that the microphone is placed as close as possible
to your mouth.
• Readjust the microphone volume.
• You may be out of range of the headset’s base unit. Move closer to the base unit.

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111

{gnresource:HSS_agfeo_logo}

{gnresource:HSS_Agfeo_ST40}

Agfeo ST 31
Agfeo ST 40

Connection:

1) Plug the 1-sided end of the DHSG cable that is marked in blue into the socket of the Agfeo ST40 which is marked with a"Headset symbol"

2) Plug the split end of the DHSG cable into the basestation of the GN 9120. The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked with "AUX" at the GN 9120 basestation.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set for DHSG Software.
(the GN 9120 DHSG is always supplied in DHSG mode)

For control, checking and setting can be carried out as follows:
Plug the headset into the basestation.

Then press the PLUS and MINUS button simulatneously for 6 seconds until the online display on the headset starts to flash.

Now your current software is displayed at the bottom.
The radio lamp represents RHL; the MUTE-Lamp DHSG and the accumulator display represents AEI.

With the help of PLUS or MINUS buttons you can toggle between particular kinds of software.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

Installation of software is confirmed when after about 10 seconds the device again automatically changes over to the charge condition


Base setting:

The adapter (small wheel) at the base station must be positioned at "A" .

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the transmission volume:

With the headset please make a call

Now one must press both PLUS and MINUS buttons on the headset simultaneously and immediately a beep is heard

Now by using the PLUS button the volume of the microphone can be increased or alternatively it can be decreased by using the MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a slight beep after 10 seconds. The settings are subsequently automatically saved .

Requirements:

GN 9120 MSH

Art.Nr.: 9120-x81-11 {gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein)

{gnresource:HSS_Alcatel_logo_klein}or {gnresource:HSS_t-com_logo_150}

IP Touch 4028                      Open Phone IP 140

IP Touch 4038                      Open Phone IP 150

IP Touch 4068                      Open Phone IP 160

 

Connection:

Connect GN 9120 MSH with the provided EHS cable connection:

{gnresource:HSS_9120_basis__ehook_anschluss} 2-western socket (RJ10 +RJ45)

2-sided end: Plug the RJ45 in the marked "AUX" jack and RJ10 in the marked "telephone icon" jack on the base station.

2-fold Y-coupling end: Plug the 3.5 mm ringing jack in the headset jack and the RJ12 in the ringing jack of the device. The additional slide-on receptacle on the Y-coupling shoul remain free during connection to an IP device!

{gnresource:HSS_alcatel_ehook_telefon_ip_klein}

 

Base setting:

{gnresource:HSS_9120_basis_einstellung_klein}

The settings knob on the base station must be set at "A".

 

Setting transmission volume::

Now try calling someone with the headset.

Now you mut press the PLUS and MINUS keys at the headset simultaneously, immediately thereafter you will hear a signal tone.

{gnresource:HSS_GN9120-�bertragungslautstärkeeinstellen-WG}

Now you can increase the volume in the microphone with PLUS or decrease it with MINUS. As confirmation, you will hear a gentle signal tone in the background after 15 seconds. Then the settings will then be stored automatically.

Important : A ring tone signal in the headset will then only be transferred if

the "Standard/Nature " ring tone signaling has been set on your telephone.

Setting:

Menu > Settings > ringing tone > tune >standard or nature

Setting telephone:

Menu> Setting > telephone > ringing connector or jack > Microphone receiver set

Prerequisite:

{gnresource:HSS_GN9120_DUO}

9129-808-111

{gnresource:HSS_Siemens-Schrift-Bild-WG}

{gnresource:HSS_openstage40}

OpenStage 40 / 60 / 80

Connection:

1.) Plug the 1-sided end of the DHSG cable that is marked in blue into the socket of your OpenStage instrument that is marked with the " Headsetsymbol " .

2.) Plug the split end of the DHSG cable into the basestation of the GN 9120 as follows:. The RJ10 plug is plugged into the complete " Telephone symbol " and the RJ45 plug into the socket marked as " AUX " at the GN 9120 basestation.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

 The GN 9120 must be set for DHSG software.
(the GN 9120 DHSG is always supplied in DHSG mode)

For control, checking and setting can be carried out as follows :
Plug the headset into the basestation.

Subsequently, press the PLUS and MINUS button simultaneously for about 6 seconds until the online display on the headset starts to flash.

The basestation displays your current software.

The radio lamp displays "RHL"; the MUTE-lamp displays"DHSG" and the accumulator display displays "AEI".
With the aid of the PLUS or MINUS button you can toggle between several types of software.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

Installation of the software is confirmed when the device once again automatically changes over to the charge condition after 10 seconds.

Base installation:

{gnresource:HSS_9120_basis_einstellung_klein}

The adapter on the basestation must be set to "A".

Adjustment of the transmission volume:

Please make a call with the headset.

Now both the PLUS and MINUS button on the headset must be pressed simultaneouly and immediately a beep is heard. Now the microphone volume can be increased by pressing the PLUS button or decreased by using the MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

As confirmation, a slight beep is heard after about 10 seconds. All the settings are subsequently automatically saved.

Important:: The dial tone signal on the headset is transmitted only when standard ringtones are used on your telephone. No "call signalling" for mp3-ringtones

Please make sure that the Jabra GN9125 is compatible with your telephone system, and set the Jabra GN9125 in the correct mode. For standard telephones and for use with Jabra GN1000, please make sure to put the Jabra GN9125 in RHL mode.

Prerequisite:

{gnresource:HSS_GN9120_DUO}

9129-808-111

{gnresource:HSS_Tiptel_Logo}


{gnresource:HSS_Tiptel85}

Tiptel 85

1) Plug the 1-sided end of the DHSG cable marked in blue into the socket of your phone marked with the "Headset symbol"

2)Plug the split end of the DHSG cable into the basestation of the GN 9350. The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 is plugged into the socket marked as "AUX" of the GN 9350 basestation.

{gnresource:HSS_9120EHS_DHSG}


Software setting:

The GN 9120 must be set for DHSG software .
(the GN 9120 DHSG is always supplied in DHSG mode)

For control, Checking and setting can be carried out as follows:
Plug the headset into the basestation.

Then press the PLUS and MINUS button simultaneously for 6 seconds until the online display on the headset starts to flash.

Now the current software is displayed on the basestation.
The radio lamp displays the "RHL"; the MUTE-Lamp "DHSG" and the accumulator display displays "AEI".

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}
With the aid of PLUS or MINUS button you can toggle between different kinds of software.
Installation of the software is confirmed when the device once again automatically changes over to the charge condition after 10 secs.


Base setting:

The adapter (small wheel) on the basestation must be positioned to "A".
{gnresource:HSS_9120_basis_einstellung_klein}


Adjustment of the transmission volume:

Please make a call with the headset.

Now you must press the PLUS and MINUS button on the headset simultaneously, immediately after which a beep is heard. Now you can increase the microphone volume by pressing the PLUS button or decrease it by pressing the MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a slight beep heard after about 10 seconds. The settings are subsequently automatically saved.

Prerequisite:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}   +     {gnresource:HSS_EHS-AV-001II}

9120-xx-11              EHS-AV-001

{gnresource:HSS_Avaya_Logo}

{gnresource:HSS_WEB_Avaya_4630IP}

This combination is compatible with the following instruments:

4610 / 4620

4621 / 4622

4625 / 4630

5420 / 5620

Connection:

1) Disconnect the network cable of your telephone.

2) Connect the EHS adapter to the "EU24/ ADJ" socket of your Avaya instrument and the "AUX" interface of your GN9120 basestation.

3) Now plug the 4-pin connection cable into the socket marked with the "Telephone symbol" on the basestation of the GN9120 and the opposite side into the "Headset interface" of your telephone.

4) Now you can reconnect the network cable to the telephone.

Software setting:

The GN 9120 must be set for DHSG software .
(the GN 9120 DHSG is always supplied in DHSG mode)

For control , you can check and make the adjustments as follows:

Plug the headset into the basestation.
Then press the PLUS and MINUS button simultaneously for about 6 seconds until the Online display on the headset starts to flash.

Now the current software is displayed on the basestation.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp displays the RHL; the Mute-Lamp DHSG and the accumulator display displays AEI. With the aid of PLUS or MINUS buttons you can alternate between different kinds of software. .

Installation of the software is confirmed when the headset once again automatically changes over to the charge condition after about 10 seconds.

Basesetting:

The adapter (small wheel) on the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Transmission volume adjustment:

Please make a call with the headset .

Now both the PLUS and MINUS button on the headset must be pressed simultaneously and this immediately results in a beep.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now you can increase the volume by using the PLUS button or alternatively decrease it by pressing the MINUS button. For confirmation, after 10 secs a slight beep is heard in the background in the headset. Settings are subsequently saved.

• Check that the mute function is off.
• Check the position of the boom arm and make sure that the microphone is placed as close as possible
to your mouth.
• Readjust the microphone volume.
• You may be out of range of the headset’s base unit. Move closer to the base unit.

Please place the new headset on the base station. The recharging light will start to flash.

{gnresource:HSS_GN9120-Headset-einlegen-WG} 

Then remove the mains adaptor from the wall socket. After approx. 1 minute of waiting, plug the mains adaptor back into the wall socket. 4 lights now need to be lit for approx. 3 seconds. The base station is then turned on again and starts charging..

{gnresource:HSS_GN9120-Basis-Leuchten-WG}

!!IMPORTANT!!! The headset must be on the base station during registration.

A wireless connection will be established as soon as you remove the headset from the base station.

Requirements:


GN 9120 E-Hook
Art.no.: 9120-xx-11 {gnresource:HSS_GN9120-Bild-WG}

Telephone:
AGFEO ST30                   +         HS30 module (from AGFEO)

{gnresource:HSS_AGFEOST30-Bild-WG}                             {gnresource:HSS_HS30Modul-Bild-WG}
from SW 3.1

Connection:

Please use the connection cable supplied with the HS30 module.

1. Set the dip switch on HS30 module jumper block X1 to "D"
2. Set the dip switch on HS30 module jumper block X2 to "N"
3. Connect the 4-pin connection cable (RJ10 to RJ10) to the plug socket with the telephone symbol on the GN9120 base station and the other end to the ST30 headset interface.
4. Connect the 8-pin connection cable (RJ45 to RJ45) to the plug socket labeled AUX on the GN9120 base station and the other end to the Agfeo HS30 module.

The RJ10 plug socket labeled with the telephone receiver (external plug socket) on the headset base station remains free.

{gnresource:HSS_GN9120BasisQuer-ohneKabel-WG}


GN 9120 software settings:


The GN 9120 must be set to DHSG software.
(the GN 9120 DHSG is always delivered in DHSG mode)

You can check and/or set it as follows:
Place the headset on the base station.

Then press the PLUS and MINUS buttons simultaneously for 6 seconds until the online display on the headset starts to flash.

Your current software is then displayed on the base.
The wireless light stands for RHL; the MUTE light for DHSG and the recharge display for AEI.

You can now switch between each software type with the PLUS or MINUS button.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

To confirm the software setting, the device automatically switches to recharge again after 15 seconds.

Setting the base:

The adjustment control (small wheel) on the base station must be set to "G".

{gnresource:HSS_GN9120-EinstellungRad-WG}



Setting the transmission volume:

Please call someone with the headset on.
Now press the PLUS and MINUS button on the headset simultaneously, a signal tone will then sound.
You can now increase the microphone volume by pressing PLUS or lower it by pressing MINUS.
After 15 seconds, a faint signal tone can be heard in the background confirming the change. The settings are then automatically saved.

ST30 settings:

In addition, a headset button needs to be programmed on the ST30. Please note the software status of your equipment and the position for programming the headset button.

Testing the wireless connection:

The GN 9120 DHSG only connects wirelessly when it is connected correctly to the HS30 module.

Prerequisite:

{gnresource:HSS_GN9120_DUO}            +       {gnresource:HSS_Akustikadapter-Bild-WG}

GN 9129-808-111       Adapter Universal ( min. Output level 10 )

{gnresource:HSS_logo_t_com}

{gnresource:HSS_OctophonF50}

Octophone F 20 / 30 / 40 / 50

Octophone IP 21 / 31 / 41

+ Adapter Universal ( min. output level 10 )

Octopus F 200 - 900 telephone system

(IMPORTANT: Even if one of the components is missing the electronic call receipt does not function!)

Connection:

1) Plug the 1-sided end of the DHSG cable that is marked in blue into the socket of the Universal adapter that is marked
with the"Headset symbol" .

2) Plug the split end of the DHSG cable into the GN 9120 basestation. The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked with "AUX" at the GN 9120 Base station.

{gnresource:HSS_GN9120-DHSG-Anschaltung-Bild-WG}
Software setting:

The GN 9120 must be set for DHSG Software .                                               ( the GN 9120 is always supplied in DHSG Mode.)

For control, checking and setting can be carried out as follows

Plug the Headset into the basestation.

Then press the PLUS and MINUS button simultaneously for 6 sec. until the online display  on the headset starts to flash.

Now your current software is displayed at the bottom.    

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}  

The radio lamp represents RHL; the Mute-Lamp DHSG and the Accumulator display represents AEI. With the help of PLUS or MINUS buttons you can toggle between particular kinds of software .

Installation of software is confirmed when after about 10 seconds the headset once again automatically changes over to the charge condition.

Base setting:

The adapter (small wheel) on the basestation must be positioned at "A" .

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of transmission volume:

please make a call with the headset.

Now both the PLUS and MINUS button on the headset must be pressed together simultaneously and this immediately results in a beep.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now by using the PLUS button the volume can be increased or alternatively it can be decreased with the aid of the MINUS button. This is confirmed by a slight beep heard in the background in the headset after about 10 seconds. The settings are subsequently saved.

Telephone setting:

Important!As soon as the headset is connected + adjusted the telephone must be reset to adopt the EHS function ..

Optionally a headset button can be provided via the telephone menu (combination: *91 >select button > change button > Headset > OK ) set up.

Requirements:

GN 9120 Standard

Art.no.: 9120-xx-01{gnresource:HSS_GN9120-Bild-WG}

GN8110 USB adapter            +        GN cable end piece 8800-00-01

{gnresource:HSS_GNUSB-AdapterBild-WG}                  {gnresource:HSS_GN8800-00-01Bild-WG}

Desktop with one of the following system programs:

WINDOWS 98/SE

WINDOWS 2000/ME

WINDOWS XP

Macintosh OS 9.0.4 (or higher)

Suse Linux from kernel 9.0

 

Connection:

1. Connect the GN cable end piece to the GN8110 USB adapter quick decoupler (QD plug).

2. Insert the 4-pin RJ10 modular connector into the socket (labeled with a telephone symbol) on the GN9120 base station.

{gnresource:HSS_GN9120BasisQuer-ohneKabel-WG}(internal socket/telephone symbol)

3. Insert the GN8110 USB plug into a free USB port on the PC.

 

Setting the audio and playback volume on a desktop:

The audio and playback volume should be set to halfway in the system settings under Sounds and Audio Device when connecting the GN9120 via a USB adapter.

{gnresource:HSS_VolumeControl-USB-WG}

 

Setting the transmission volume on the GN9120:

Please call someone with the headset on.

Now press the PLUS and MINUS button simultaneously, a signal tone will then sound.

You can now increase the microphone volume by pressing PLUS or lower it by pressing MINUS.

After 15 seconds, a faint signal tone can be heard in the background confirming the change. The settings are then automatically saved.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

 

Adjustment on the GN9120 base station:

The adjustment control (small wheel) on the base station must be set to "A".

{gnresource:HSS_GN9120-EinstellungRad-WG}  

 

Requirements:


GN 9120 E-Hook
Art.-Nr.: 9120-xx-11 {gnresource:HSS_GN9120-Bild-WG}

Telephone:
{gnresource:HSS_CS410-Bild-WG)

Elmeg CS410 (Important! The electronic call acceptance function does not operate in the answering machine module!)

Elmeg CS410-U (Entire function)

Elmeg CS290-U (Entire function)


Connection:

DHSG connection to versions GN9120 with the provided EHS Y-cable (marked in blue) to the Elmeg CS410 as follows:

1-sided end of the Y-cable (RJ45) (marked in blue):

RJ45 jack identified with headset on Elmeg CS410!

2-sided end of the Y-cable (RJ10 & RJ45)

On GN9120 base station, RJ45 to AUX-jack, RJ10 to telephone-icon jack!

The RJ10-jack identified with the handset should remain free on the headset-base station!

{gnresource:HSS_9120EHS_DHSG}

Setting software GN 9120:

The GN 9120 must be setto DHSG software.
(The GN 9120 DHSG is always supplied in the DHSB mode)

To check this you can set it as follows:
Plug the headset into the base station.

Then press the PLUS and MINUS keys simultaneously for 6 seconds till the online-indicator begins to flash on the headset.

Now your actual software is shown to you.

The radio lamp is for RHL; the MUTE-lamp is for DHSG and the accu-indicator is for AEI:

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

Now you can switch between the individual software types with the PLUS or MINUS keys.
To confirm the setting of the software change over automatically after 15 seconds into the load status.


Base setting:

The setting knob (small cog) must be set at "A" on the base station.

{gnresource:HSS_GN9120-EinstellungRad_WG}


Setting transmission volume

Now try calling someone with the headset.

You must now press the PLUS and MINUS keys at the headset simultaneously, thereafter you will hear a signal tone.

Now you can increase the volume in the microphone with PLUS or decrease it with MINUS.

{gnresource:HSS_GN9120-�bertragungslautstärkeeinstellen-WG}
As confirmation you will hear a gentle signal tone in the background after 15 seconds. Then the settings will be stored automatically.


Setting on CS410/410-U/290-U:

1. The function "DHSG-headset" must be enabled for the following menu levels.

Press >MENU >ACCOUSTIC >HEADSET >DECT HEADSET (DHSG)

Now the hook must be behind DECT headset (DHSG).

2. In addition a headset key must be programmed for Elmeg.

You can set this via the provided CD or via the following key combinations.

To begin with insert this Code:

**46782551## and then press following keys

>ESC >MENU >NUMBERPROGRAMMING >TARGET SELECTION >FUNCTION

Now select a key on the control panel and set the HEADSET function.

Test radio set-up:

The GN 9120 DHSG will only set the radio if it is properly connected to the Elmeg.

Prerequisite:

{gnresource:HSS_GN9120_DUO}  +  {gnresource:HSS_Akustikadapter-Bild-WG}

GN 9129-808-111    Akustik-Adapter ( min. ouput level 10 )

{gnresource:HSS_Siemens-Schrift-Bild-WG}
{gnresource:HSS_OptiPoint-Bild-WG}

Opti Point 410 standard / advance

Opti Point 420 standard / advance

Opti Point 500 basic / standard / advance

Opti Point 600

+ Opti Point Acoustic Adapter (min output level 10)

+ HiPath Telephone system

HiPath   500 from V.5

HiPath 1220 from V2.1 Build 032

HiPath 2000 from V1.0

HiPath 3000 from V3 SMR 14

HiPath 3000 from V4 SMR 7

HiPath 4000 from V1

(IMPORTANT: If one of the components is missing, electronic call receipt does not function!)

Connection:

1) Plug the 1-sided end of the DHSG cable that is marked in blue with the end of the socket of the OptiPoint Acoustic adapter that is marked with the"Headset symbol"

2)Plug the split end of the DHSG cable into the basestation of the GN 9120. the RJ10 Plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked as "AUX" at the GN 9120 basestation.

{gnresource:HSS_GN9120-DHSG-Anschaltung-Bild-WG}

Software setting:

Das GN 9120 must be set for DHSG Software .                                              
( the GN 9120 is always supplied in DHSG-Mode.)

For control, checking and setting can be carried out as follows

Plug the headset into the basestation.

Then press the PLUS and MINUS button simultaneously for 6 seconds until the online display   on the headset starts to flash.

Now your current software is displayed at the bottom.    

   {gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp represents RHL; the Mute-Lamp DHSG and the accumulator display represents AEI. With the help of PLUS or MINUS buttons you can toggle between particular kinds of software.

Installation of the software is confirmed when after about 10 seconds the headset once again automatically changes over to the charge condition.

Base setting:

The adapter (small wheel) at the base station must be positioned at "A ".

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the transmission volume :

With the headset please make a call .

Now both the PLUS and MINUS buttons on the headset must be simultaneously pressed and this immediately results in a beep.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now by using the PLUS button the volume can be increased or alternatively it can be decreased by using the MINUS button . This is confirmed by a mild beep that is heard after 10 seconds in the background in the headset. Subsequently the settings are saved.

Telephone setting:

Important! As soon as the headset is connected and adjusted, the OptiPoint is reset to adopt the EHS Function.

Optionally, a head set button can be selected through the (Combination: 91 >Select button > change button > Headset > OK ) set up.

Your headset may need pairing to the base. Refer to page 7 “Registering a new master headset” in this
reference guide.

Prerequisite:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}    {gnresource:HSS_SNOM_360_Voip}      {gnresource:HSS_snom_ehs_adapter(1)}

GN 9120-xx-11     Snom 320 /360 / 370    Snom EHS-Box

(*Snom 320/360 > ab Software release 6.5.8 nähere Infos unter http://www.snom.com/wiki/index.php/Accessories/Interface_Box )

(**Snom 370 > ab Software 7.1.28

Connection:

{gnresource:HSS_snom_ehs_anschluss}

1) Connect the supplied RJ10 connection cable of GN9120 to RJ10 with the "Headset-Interface" of the Snom Instrument and with the" complete telephone symbol "to the GN9120 Base station.

2) Connect the Snom EHS Box with the " EXT " port of your Snom instrument and the " AUX" interface at your GN9120 basestation.

Software setting:

The GN 9120 must be set to DHSG Software
(The GN 9120 EHS is always provided in DHSG Mode)

To check the installed software,proceed as follows:

Plug the headset into the basestation and press the PLUS and MINUS button simultaneously
for about 6 seconds until the Online display on the headset starts to flash.

Now your current software is displayed at the base station.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp represents RHL; the MUTE-LED DHSG and the accumulator display AEI.

With the help of PLUS and MINUS button you can toggle between different kinds of software.

Installation of the software is confirmed when the basestation automatically changes to the charge condition after about 10 seconds.

Base setting:

Set the telephone setup switch ( A-G ) at "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the transmission volume :

please make a call using the headset.

Now on the headset both the PLUS and MINUS button must be pressed simultaneously and this immediately results in a beep.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now by using the PLUS button you can increase the volume of the microphone or alternatively decrease it by using the MINUS button.

This is confirmed by a slight beep heard in the headset after about 5 seconds. The settings are subsequently automatically saved.

Check that all the cords and plugs are connected correctly. Check that the power adapter is plugged in and has power.Check that the on-line indicator is lit. If it is not, place the headset in the base unit and take it out again. Check that the battery is charged. If the battery is fully charged, the battery charging indicator on the base unit will light when the headset is placed correctly in the base unit.

Prerequisite:

{gnresource:HSS_GN9120_DUO}   +     {gnresource:HSS_AZ-Adapter-Bild-WG}+ {gnresource:HSS_DE-EHS001_klein}

GN 9129-808-111       Comfort-Adapter          DE-EHS-001


{gnresource:HSS_logo_t_com}

{gnresource:HSS_T-comfort-830-Bild-WG}

T- Comfort 730 / 830


System:

830 DSL   from Software 5.2
930 DSL   from Software 3.2


Connection:

Connect the provided 4-pin RJ10 connection cable to the socket marked with the "Telephone symbol" at the basestation of GN 9120 and the opposite side with the "Headset socket" of the Comfort-Adapter.

Now plug the 8-pin RJ45 plug of DE-EHS-001 connection cable into "AUX" socket at the GN 9120 base station.

Connect the hollow socket plug with the socket of the AZ adapter marked with a "bell symbol" and plug the 6-pin Western plug into the "second receiver socket" of the Comfort-Adapter.

(The GN9120 EHSis always provided in DHGS Mode) )

For checking the installed software proceed as follows:
Plug the headset into the basestation and press the PLUS and MINUS button
simultaneously for about 6 seconds until the online display on the headset starts to flash.

Now the current software is displayed on the basestation.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp displays RHL; the Mute-LED DHSG and the accumulator display displays AEI.

With the aid of PLUS and MINUS button you can toggle between particular kinds of software.

Installation of the software is confirmed when after about 10 seconds the base station again automatically changes over to the charge condition

The adapter ( small wheel ) at the base station must be positioned at "A" .

{gnresource:HSS_GN9120-EinstellungRad-WG}

Adjustment of the transmission volume:

With the headset please make a call .

No, none of our Jabra products contains PCB, polychlorinated biphenyl.

GN 9120 standard or E-Hook

 

{gnresource:HSS_AEH-Modul-Bedienungsblatt-WG}

The adjustment control (small wheel) on the base station must be set to "A".

Please call someone with the headset on.

A beep every 15 seconds means that the mute function is on. A beep every 10 seconds means that you are out of range (up to 100 m, depending on environment) of the headset’s base unit. Move closer to the base unit. A beep every 20 seconds means that the battery charge is low and needs to be recharged.

To be able to register the Jabra GN9120 DG, the DECT telephones/base stations must already have the system authentication code "0000".

If you do not know whether your telephone accepts this code, then look for detailed information in your telephone manual. This information can normally be found under "Registering/deregistering mobile devices". It explains how to register GAP compatible mobile devices and how to change the corresponding code.

Already tested on:

Telephone equipment:

 

Manufacturer	Type of equipment
AGFEO	AS1x/AS2x/AS3x from V6.2f
AGFEO	AS 40 P
ALCATEL	4400 from Release 5.0
ALCATEL	OMNI PCX Office from Release 2.1 and 3.1
ALCATEL	OMNI PCX Enterprise IBS NG
ALCATEL	OMNI PCX Enterprise IBS RBS
DeTeWe **	OPEN COM 100
DeTeWe **	OPEN COM 1000
PANASONIC	KX-TDA 15 / 30
PANASONIC	KX-TDA 100 / 200
TELEKOM **	T-COMFORT 730/830 DSL
TELEKOM **	T-COMFORT 930 DSL
TELEKOM	T-OCTOPUS OPEN 730/830
TELEKOM	T-OCTOPUS OPEN 930

Base station for up to 6 mobile devices:

 

Manufacturer	Base station
AEG	8000 Voice
AUDIOLINE	6500
B & O	BeoCom 6000
DeTeWe	BeeTel 440i/445i
DeTeWe	BeeTel 450i/455i
DeTeWe	BeeTel 550i
DORO	DECT 8075
LOEWE	AlphaTel 4000
PANASONIC	KX-TCD 200
PANASONIC	KX-TCD 445
PANASONIC	KX-TCD 560
PANASONIC	KX-TCD 705 G
PANASONIC	515 GM
KIRK	DECT RFP4
KPN	Chicago 500
SIEMENS	Gigaset 301x/401x
SIEMENS	Gigaset 41xx
SIEMENS	Gigaset SL 100/150/740
SIEMENS	Gigaset SL550/SL555
SIEMENS	Gigaset C100/200
SIEMENS	Gigaset A140/240/345
SIEMENS	Gigaset A200/A340
SIEMENS	Gigaset C340/450
SIEMENS	Gigaset C345/C455
SIEMENS	Gigaset E450/E455
SIEMENS	Gigaset S100/S150
SIEMENS	Gigaset S440/S445
SIEMENS	Gigaset S450/S455
SIEMENS	Gigaset S 645
SIEMENS	CX 253/353 isdn
SIEMENS	SX 253/353 isdn
SIEMENS	CX 345 isdn
SWATCH	Cordless II
TELEKOM	SINUS 512
TELEKOM	SINUS 6220
TELEKOM	T-Sinus 710/710A/710K
TELEKOM	T-Sinus 711/711A/711K
TELEKOM	T-Sinus 712/712A/712K
TELEKOM	T-Sinus 721/721A/721K
TELEKOM	T-Sinus 722/722A/722K
TOPCOM	3500

** With those supplied from January 2006 (the software needs to be updated with older devices)

GN 9120 standard or E-Hook

Prerequisite:

{gnresource:HSS_GN9120_DUO}      +     {gnresource:HSS_AZ-Adapter-Bild-WG}+ {gnresource:HSS_DE-EHS001_klein}

GN 9129-808-111             AZ-Adapter                         DE-EHS-001

{gnresource:HSS_Detewe_logo}

{gnresource:HSS_OpenPhone65-WG}

Open Phone 63 / 65

System:

Open Com   100   from Software 5.2

Open Com   1000   from Software 3,2

Connection:

Connect the RJ10 4-pin connection cable to RJ10 using the socket marked with the "Telephone symbol" at the GN 9120 basestation and the opposite side with the "Headset socket" of AZ-Adapter.

Now plug the 8-pin RJ45 plug of the DE-EHS-001 connection cable into the "AUX" socket in the GN 9120 basestation.

Connect the hollow socket plug with the socket of the AZ-adapter marked with a "bell symbol and plug the 6-pin Western plug into the "second reciever socket" of the AZ-Adapter.

Software setting:

For checking the installed software proceed as follows:

Plug the headset into the basestation and press PLUS and MINUS button

for about 6 secs simultaneously until the online display on the headset starts to flash

Now the current software is dsiplayed on the basestation.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp represents RHL; the MUTE-LED DHSG and the accumulator display represents AEI.

With the help of PLUS and MINUS button you can toggle between the particular kinds of software.

Installation of the software is confirmed when after about 10 seconds the basestation once again automatically changes to the charge condition

The adapter (small wheel) at the basestation must be positioned at "A" .

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the transmission volume:

Please make a call with the headset.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

The GN9120 has two different range functions:

1) Hi-Power Mode: max range 150 m; max. radiated power 63 mW (factory setting)

2) Low-Power Mode: max range 25 m; max. radiated power 4 mW

Setting Low-Power Mode:

 Place the headset on the base station.

 Now press and hold the MINUS and MULTIFUNCTION button on the headset simultaneously until the online display on the headset begins to blink.

  > 

Now release both buttons and wait until the online display on the headset goes out. (blinks approx. 3-5 seconds) The GN9120 is now in Low-Power mode. You can check the settings by taking the headset off the station and watching the online display on the station.

 Every 10 seconds this should go out for 1 second and then light up again for a constant 10 seconds.

 

Setting Hi-Power Mode:

  Place the headset on the base station.

 Now  press and hold the PLUS and MULTIFUNCTION button on the headset simultaneously until the online display on the headset begins to blink.

  > 

Now release both buttons and wait until the online display on the headset goes out. (blinks approx. 3-5 seconds) The GN9120 is now in Hi-Power mode. You can check the settings by taking the headset off the station and watching the online display on the station.

 This should be constantly lit and must no longer go out every 10 seconds.

 

Prerequisite:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}

GN 9120-xx-11

{gnresource:HSS_Detewe_logo}

{gnresource:HSS_Aastra_70_IP}

Open Phone 71 / 73 / 75
Open Phone 73IP / 75IP


Connection:

1) Plug the 1-sided end of the DHSG-cable that is marked in blue into the socket of your telephone that is marked with the" headset symbol"

2)Plug the split end of the DHSG-cable into the basestation of the GN 9120. The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked as "AUX" of the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

 The GN 9120 must be set for DHSG Software .
(the GN 9120 DHSG is always supplied in DHSG Mode)

For control, checking and setting can be carried out as follows:
Plug the headset into the base station.

Then press the PLUS and MINUS button simultaneously for 6 seconds until the online display on the headset starts to flash.

Now your current software is displayed at the base.
The radio lamp represents "RHL"; the MUTE-Lamp DHSG" the accumulator display represents "AEI".

With the help ofPLUS or MINUS buttons you can toggle between particular kinds of software.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

Installation of the software is confirmed when after about 10 seconds the device again changes over automatically to the charge condition
.

Base installation:

{gnresource:HSS_9120_basis_einstellung_klein}

The adapter at the base station must be positioned at" A " .

Adjustment of the transmission volume :

With the headset please make a call .

Now both the PLUS and MINUS buttons on the headset are pressed simultaneously and immediately a beep is heard. Now by using the PLUS button, the microphone volume can be increased or alternatively decreased by using the MINUS button. 

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a slight beep after about 10 sec. Subsequently the settings are automatically saved.

Telephone setting:

Open Phone 71:  Menu > Settings > Audio > Headset ON                               
Open Phone 73 / 75 incl. IP:  Menu > Setting  > Headset > Headset ON           

                                 

GN 9120 E-Hook

 9120-xx-11

Tenovis TM/TH13 or T3/T3IP Comfort/Classic

{gnresource:HSS_tenovisTM13-WG}

(A CTI AUDIO LINK adapter is always required for T3 devices and a CTI IP AUDIO LINK adapter for T3 IP devices) 

EQUIPMENT

Integral 5

Integral 33/55

Integral 3 (starting from software E5.200)

(electronic answering with TS13 is only possible in connection with Integral 3)

Connection:

Please use the Y cable "without the blue band". 

1. The individual 6-pin RJ12 modular connector must be connected to the X/Y socket on the AEI interface.

2. Insert the 8-pin RJ45 modular connector into the AUX socket on the GN 9120 base station.

3. Insert the 4-pin RJ10 modular connector into the GN 9120 base station socket labeled with the telephone symbol.

Prerequisite:

{gnresource:HSS_GN9120_DUO}

9129-808-111

{gnresource:HSS_Tiptel_Logo}


{gnresource:HSS_Tipel275}

Tiptel 275

From Software V.1.25 complete function

Connection:

1) Plug in the 1-sided end of the DHSG cable that is marked in blue into the "HS 2" socket of your telephone.

2) Plug the split end of the DHSG cable into the basestation of the 9350. The RJ10 plug is plugged into the socket with the "Telephone symbol" and the RJ45 is plugged into the socket marked as "AUX" on the GN 9350 basestation.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set to DHSG software .
(the GN 9120 DHSG is always supplied in DHSG mode)

For control, checking and setting can be carried out as follows:
Plug the headset into the base station.

Then press the PLUS and MINUS button simultaneously for about 6 sec until the online display on the headset starts to flash.

Now the current software is displayed at the base.
The radio lamp displays the "RHL"; the MUTE-Lamp "DHSG" the accumulator display displays"AEI".

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

With the aid of the PLUS or MINUS button you can toggle between different kinds of software. Installation of the software is confirmed when the device once again automatically changes over to the charge condition after about 10 secs.

Basic setting:

The adapter (small wheel) on the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}


Adjustment of the transmission volume:

Please make a call with the headset.

Now the PLUS and MINUS button on the headset must be pressed simultaneously and this immediately results in a beep. With the aid of PLUS button the volume of the microphone can be increased and with the aid of MINUS button it can be decreased.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

As confirmation, a slight beep is heard after about 10 seconds. All the settings are subsequently automatically saved.

Telephone setting:

Menu > Setting > Telephone > Headset > DHSG > OK

Requirements:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}

9120 -xx-11

{gnresource:HSS_logo_t_com}


{gnresource:HSS_ComfortPro_P500_IP_Klein}

Comfort Pro P 300 /500 IP

Connection:

1) Plug one end of the DHSG-cable marked in blue into the
"Headset icon" jack of the telephone.

2) Plug the split end of the DHSG-cable into the base station of the GN 9120. Plug the RJ10 connector into the jack marked with the "telephone icon" and RJ45 connector into the jack marked "AUX" on the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set to DHSGsoftware.
(The GN9120 EHS is always supplied in the DHSG mode. )

To check the set software proceed as follows:

Plug the headset into the base station and press the PLUS and MINUS buttons
for 6 seconds simultaneously till the Online-indicator begins to blink on the headset.

Now your actual software is shown to you.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp is for RHL"; the MUTE-LED for "DHSG" the accu-indicator is for " AEI.

With the PLUS and MINUS buttons you can now switch between the individual software types.
To confirm the set software, the base station automatically changes after 10 seconds again into the charge status.

Base setting:

Set the telephone-set-up switch (A-G) to "A"

{gnresource:HSS_9120_basis_einstellung_klein}

Setting transmission volume:

Try calling someone with your headset.
Now press the PLUS and MINUS buttons simultaneously, then you will immediately hear a signal tone.

{gnresource:HSS_GN9120-�bertragungslautstärkeeinstellen-WG}

Now you can increase the microphone volume with PLUS or decrease it with MINUS .

As confirmation a gentle signal tone sounds in the headset after 5 seconds. Then the settings will be stored automatically.

Setting telephone:

In addition a headset button must be set on Comfort Pro.

Enable Menu > Entire menu > Telephone settings > Headset

Requirements:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}         +  {gnresource:HSS_Akustikadapter-Bild-WG}

 GN 9120 - xx - 11   +  Adapter Universal  ( min. version 10 )



{gnresource:HSS_logo_t_com}


{gnresource:HSS_Comfort_Open_p300ip}

Comfort Open P 100/300 IP


Equipment:

Comfort Open

If any of the components are missing, then the electronic call acceptance function will not work.


Connection:

1. Plug one end of the DHSG cable marked in blue with
the "headset icon" jack of the universal adapter.

2. Plug the split end of the DHSG cable into the base station of GN 9120.
The RJ10 connector into the "telepnone icon" and the RJ45 connector
into the jack marked with "AUX" on the GN 9120 base station.


{gnresource:HSS_GN9120-DHSG-Anschaltung-Bild-WG}
Software setting:

The GN 9120 must be set at the DHSG software.
(The GN 9120 EHS is always supplied in the DHSG mode. )

To check the set software proceed as follows
Plug the headset into the base station and press the PLUS and MINUS keys
for about 6 seconds simultaneously till the Online-indicator begins to flash on the headset.

Now your actual software is displayed to you on the base station.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp stands for RHL; the MUTE-LED for DHSG and the accu-indicator for AEI.
Using the PLUS and MINUS buttons you can now switch between the individual software types.

To confirm the set software the base station automatically switches after 10 seconds back into the charge status.


Base setting:

Set the telephone set-up switch (A-G) to "A"

{gnresource:HSS_9120_basis_einstellung_klein}


Setting the transmission volume:

Try calling someone with your headset.

Now press the PLUS and MINUS buttons simultaneously on the headset, you will then hear a signal tone immediately.

{gnresource:HSS_GN9120-�bertragungslautstärkeeinstellen-WG}

Now you can increase the microphone volume with PLUS or decrease with MINUS button.
As confirmation, you will hear a gentle signal tone in the headset after 5 seconds. Then the settings will be stored automatically.

Telephone setting:

In addition a headset button must be set on Comfort Open.

Important! As soon as the headset has been connected and set, then a Reset must be carried out with the OptiPoint, so that the EHS function can be accepted.

Prerequisite:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}
9120-xx-11


{gnresource:HSS_Tiptel_Logo}


{gnresource:HSS_Tipel275}

Tiptel 275

From Software V.1.25 complete function

Connection:

1) Plug the 1-sided end of the DHSG cable that is marked in blue into the "HS 2" socket of your telephone.

2)Plug the split end of the DHSG cable into the basestation of the GN 9350.The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked as "AUX" at the GN 9350 basestation.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set for DHSG software.
(the GN 9120 DHSG is always supplied in DHSG Mode)

For control, checking and setting can be carried out as follows:
Plug the headset into the basestation.

Subsequently press the PLUS and MINUS button simultaneously for about 6 seconds until the online display on the headset starts to flash.

Now the current software is displayed on the basestation.
The radio lamp displays the "RHL"; the MUTE-Lamp "DHSG" the accumulator display represents"AEI".

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

With the aid of the PLUS or MINUS button you can toggle between different kinds of software. Installation of the software is confirmed when the device automatically changes over to the charge condition again after about 10 seconds.

Base setting:

The adapter (small wheel) on the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the transmission volume:

Please make a call using the headset

Now the PLUS and MINUS button on the headset must be pressed simultaneously and it immediately results in a beep. With the help of PLUS button the volume of the microphone can be increased and alternatively it can be decreased by using the MINUS button

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a slight beep heard after about 10 seconds. All the settings are subsequently automatically saved.

Telephone setting:

Menu > Setting > Telephone > Headset > DHSG > OK

Prerequisite:

{gnresource:HSS_GN9120_DUO}  +  {gnresource:HSS_snom_ehs_adapter(1)}

9129-808-111             Snom-EHS Box  ( bei Snom erhältlich )

{gnresource:HSS_Snom_logo}


{gnresource:HSS_snom_360}

Snom 320 / 360 / 370

(*Snom 320/360 > ab Software release 6.5.8 nähere Infos unter http://www.snom.com/wiki/index.php/Accessories/Interface_Box )

(**Snom 370 > ab Software 7.1.28

Connection:

{gnresource:HSS_snom_ehs_anschluss}


1) Connect the RJ10 connection cable provided to 9120 with the "headset interface" of the Snom instrument and with the " complete telephone symbol "at the GN9120 base station.

2) Connect the Snom EHS box to the " EXT " socket of your Snom instrument and the " AUX" interface of your 9120 basestation.

Software setting:

The 9120 must be set for DHSG Software
(The 9120 EHS is always supplied in DHSG mode.)

To check the installed software,proceed as follows:

Plug the headset into the basestation and press the PLUS and MINUS button simultaneously
for about 6 seconds until the online display on the headset starts to flash.

Now your current software is displayed on the basestation.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-Farblich-WG}

The radio lamp displays RHL; the MUTE-LED DHSG and the accumulator display AEI.

With the aid of PLUS and MINUS button you can toggle between different kinds of software.

Installation of the software is confirmed when after about 10 seconds the base station again automatically changes over to the charge state

Base setting:

Set the telephone setup switch ( A-G ) at the position "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the transmission volume :

With the headset please make a call . .

Nowt both the PLUS and MINUS button on the headset must be pressed simultaneously and immediately a beep is heard.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now with the aid of the PLUS button you can increase the volume of the microphone or alternatively with the aid of MINUS button you can reduce it.

This is confirmed by a slight beep heard in the headset after about 5 seconds. The settings are subsequently automatically saved.

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111

{gnresource:HSS_logo_t_com}

{gnresource:HSS_ComfortPro_P500_IP_Klein}

Comfort PRO P 100/ 300/ 500

System:

Comfort Open

Connection:

1.) Plug the 1-sided end of the DHSG cable marked in blue into the socket of your telephone marked with the " Headset symbol " .

2.) Plug the split end of the DHSG cable into the basestation of the GN 9120. The RJ10 plug is plugged into the socket with the complete " Telephone symbol " and RJ45 plug into the socket marked with " AUX "at the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set for DHSG Software
( The GN 9120 EHS is always supplied in DHSG Mode.)

To check the installed software,proceed as follows:

Plug the headset into the base station and press the PLUS and MINUS button simultaneously
for about 6 seconds. till the Online-display on the headset starts to blink.

Now the current software is displayed at the base station.

The radio lamp represents RHL; the MUTE-LED DHSG and the accumulator display AEI.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

With the help of PLUS and MINUS button now you can toggle between particular kinds of software.
Installation of the software is confirmed when the basestation once again automatically changes over to the charge condition after about 10 seconds.

Base installation:

Set the telephone setup switch ( A-G ) at the position "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Transmission volume adjustment:

Please make a call using the headset .

Now on the headset both the PLUS and MINUS button must be pressed simultaneously and this immediately results in a beep.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now by using the PLUS button the volume of the microphone can be increased or alternatively it can be decreased by using the MINUS button.

This is confirmed by a slight beep in the headset after about 5 seconds. The settings are subsequently automatically saved.

Telephone installation:

Additionally a Headset button must be installed at Comfort PRO .

Menu > Overall menu > Telephone installation > activate Headset

Requirements:


GN 9120 E-Hook

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}

Article number: 9120- xx -11


Telephone:
{gnresource:HSS_innovaphone_IP230_klein}

Innovaphone IP 230

Connection:

Take the DHSG-cable and plug the individual end of the cable (marked in blue) into the jack with the "headset icon" of the Innovaphone IP 230
Then plug the RJ10 connector into the telephone" jack and the RJ 45 connector into the jack marked " AUX" of your GN 9120.

{gnresource:HSS_GN9120-DHSG-Anschaltung-Bild-WG}
Setting GN 9120

The GN 9120 must be set to DHSG Software.
(The GN 9120 DHSG is always delivered in the DHSG mode).

To check this you can set it as follows:

Plug the headset into the base station.

Then press the PLUS and MINUS button for approximately 6 seconds simultaneously till the
Online-indicator on the headset begins to flash.

Now your actual software is shown to you on the base station.
The flashing light is for RHL ; the Mute lamp is for DHSGand the accu-indicator for AEI .

With the Plus or Minus button you can now switch between the individual software types.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-Farblich-WG}

As confirmation of the adjusted software, the equipment switches over automatically
6 again after approx. 10 seconds to the charge status.


Base setting:

The wheel on the base station must be set to "A".

{gnresource:HSS_9120_basis_einstellung_klein}



Setting the microphone volume:

Now try calling someone with the headset, if the person you call does not hear you very clearly, then you must press the PLUS and Minus button simultaneously, and you will hear a signal tone immediately thereafter.
Now you can increase the microphone volume with the PLUS or reduce it with Minus.

{gnresource:HSS_GN9120-�bertragungslautstärkeeinstellen-WG}

As confirmation you will hear a gentle signal tone in the background after 10 seconds. Then the settings will be stored automatically.

Check the battery is correctly fitted inside the headset, and/or the headset is placed correctly in the
base

Requirements:

GN 9120 E-Hook

Art.no.: 9120-xx-11{gnresource:HSS_GN9120-Bild-WG}

TELEKOM Octophon F
        
{gnresource:HSS_OctophonF50}                            

Octophon F 20 / 30 / 40 / 50

Octophon F IP 21 / 31 / 41
 
+ Universal adapter  ( min. version 10 )

{gnresource:HSS_Akustikadapter-Bild-WG}
 
 
EQUIPMENT

Octopus F

F 900 starting from V 1.0
F 200-600 starting from V 4.0
 
Connection:

1) Insert the 1-sided blue end of the DHSG cable into the universal adapter plug socket labeled "Headset symbol".

2) Insert the split end of the DHSG cable into the GN 9120 base station and insert the RJ10 jack into the plug socket with the compl "Telephone symbol" and the RJ45 jack into the plug socket labeled "AUX" on the GN 9120 base station.

{gnresource:HSS_Akustik-Adapter-Anschlußbild-WG}
{gnresource:HSS_GN9120-DHSG-Anschaltung-Bild-WG}

GN 9120 software settings:

The GN 9120 must be set to DHSG software (GN 9120 DHSG is always delivered in DHSG Mode)

You can check and/or set it as follows:

Place the headset on the base station.

Then press the PLUS and MINUS buttons simultaneously for 6 seconds until the online display on the headset starts to flash.

Your current software is then displayed on the base.{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The wireless light stands for RHL; the MUTE light for DHSG and the recharge display for AEI.

You can now switch between each software type with the PLUS or MINUS button.

To confirm the software setting, the device automatically switches to recharge again after 15 seconds.

Setting the base:

The adjustment control (small wheel) on the base station must be set to "A".

{gnresource:HSS_GN9120-EinstellungRad-WG} 

Setting the transmission volume:

Please call someone with the headset on.

Now press the PLUS und MINUS button on the headset simultaneously, a signal tone will then sound.

You can now increase the microphone volume by pressing PLUS or lower it by pressing MINUS.

After 15 seconds, a faint signal tone can be heard in the background confirming the change. The settings are then automatically saved.
 
Settings on the Octophon:
 
You can also program a headset button on the Octophon via the equipment.

(combination: *91 >select button > change button > Headset > OK)

Testing the wireless connection:

The GN 9120 DHSG only connects wirelessly when it is connected correctly to the universal adapter.

Place the headset on the base station.

Then press the PLUS and MINUS buttons simultaneously for 6 seconds until the online display on the headset starts to flash.

Your current software is then displayed on the base. The wireless light stands for RHL; the MUTE light for DHSG and the recharge display for AEI.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

You can now switch between each software type with the PLUS or MINUS button.

To confirm the software setting, the device automatically switches to recharge again after 15 seconds.

Prerequisite:

{gnresource:HSS_GN9120_DUO}   +  {gnresource:HSS_EHS-AV-001II}

9129-808-111       EHS-AV-001

{gnresource:HSS_Avaya_Logo}


Avaya 2420 Version " B "

Callmanager Software 4.0

Connection:

1)Disconnect the network cable of your telephone.

2) Connect the EHS adapter to the " EU24/ ADJ " socket of your Avaya instrument and the   
" AUX " interface of your GN 9120 basestation.

3) Plug the 4-pin connection cable (RJ10 to RJ10) into the socket marked with a "telephone symbol" on the basestation of GN 9120 and the opposite side into the "headset interface" of your telephone.

4) Now you can reconnect the network cable to the telephone.

Software setting:

The 9120 must be set for DHSG sofware.
(tThe 9120 DHSG is always supplied in DHSG mode)

For control,you can check and make adjustments as follows:

Plug the headset into the basestation.
Then press the PLUS and MINUS button simultaneously for about 6 seconds until the online display on the headset starts to flash.

Now the current software is displayed on the basestation.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-Farblich-WG}

The radio lamp displays the RHL; the Mute-Lamp DHSG and the accumulator display displays AEI.
With the help of PLUS or MINUS buttons you can toggle between different kinds of software.

Installation of the software is confirmed when the headset automatically changes over to the charge condition again after around 10 seconds.

Base setting:

The adapter (small wheel) on the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of transmission volume:

Please make a call with the headset ..

Now both the PLUS and MINUS buttons on the headset must be pressed simultaneously and this immediately results in a beep.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now the volume can be increased by using the PLUS button or alternatively decreased by using the MINUS button. For confirmation, a slight beep can be heard in the background in the headset after 10 secs. The settings are subsequently saved.

Make sure your telephone’s volume control is set to a mid position or lower. If necessary, adjust your
microphone volume on the headset to a lower setting

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111

{gnresource:HSS_Tenovis_Logo_klein}
{gnresource:HSS_tenovisTM13-WG}

Tenovis TM/TH13 or T3/T3IP Comfort/Classic

( For T3 instruments the CTI AUDIO LINK Adapter is always required and

for theT3 IP a CTI IP AUDIO LINK Adapter ) is required.

System:

Integral 3 ( ab Software E5.200 )

Integral 5

Integral 33 / 55

Electronic call receipt for TS13 is possible only in conjunction with Integral 3

Connection:

1-sided end:

Plug the 1-sided end of the GH-cable into the socket marked as  X/Y

of your telephone.

2-sided end:

Plug RJ10 is plugged into the socket with the complete "Telephone symbol" and the 8-pin RJ45 plug is plugged into the socket marked as "AUX" at the GN 9120 basestation.

{gnresource:HSS_GN9120-DHSG-Anschaltung-Bild-WG}

Software setting:

The GN 9120 must be set for AEI Software .                                               ( the GN 9120 is always delivered in DHSG-Mode. )

For control, checking and setting can be carried out as follows

Plug the headset into the basestation.

Then press the PLUS and MINUS button simultaneously for 6 seconds until the online display  on the headset starts to flash.

Now your current software is displayed at the base.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}    

The radio lamp stands for RHL; the Mute-Lamp for DHSG and the Akku-display for AEI. With the aid of PLUS or MINUS buttons you can toggle between different kinds of software.

Installation of the software is confirmed when the device once again automatically changes over to the charge condition after about 10 seconds.

Base installation:

The adapter (small wheel) at the base station must be set to "A" .

{gnresource:HSS_9120_basis_einstellung_klein}

Transmission volume adjustment:

Please make a call with Headset .

Now both the PLUS and MINUS button on the headset must be pressed together simultaneously and this immediately results in a beep.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Now using the PLUS button the volume can be increased or altenatively it can be reduced by using the MINUS button As confirmation, a mild beep is heard in the background in the headset after 10 secs . Subsequently the settings are saved.

Telephone installation:

For Integral 33/55 with T3 Comfort and T3 Clasic Telephone

1. In the user menu under Settings/ CTI-Audio-Link / Comfort Headset to be set at AEI

New function on the GN9120DG:

To AGFEO installations, even with small SIEMENS and T-Combase stations calls can be transferred to the headset by a single button click, and they can even be connected back to the cell phone again.

Requirements:

{gnresource:HSS_Siemens-SL100-WG}SIEMENS GIGASET starting at the SL100 Series (Base station only! e.g. SL1 alone not possible! )

{gnresource:HSS_T-Sinus711-WG}TELEKOM SINUS starting at the M 711 Series (Base station only! e.g. M 701 alone not possible! )

{gnresource:HSS_GN9120-Bild-WG}GN 9120 DG starting from March 2005 deliveries (SW 02/05)

( You can find a list of all the telephones that support this function at the end of this article ) 

Settings:

The GN9120DG is registered to the base station by means of the paging button. (You can also find pairing information here in the online support)

Now activate "Int. switch on"

{gnresource:HSS_Siemens-SL1-Display-INT-zuschalten-WG}

You will find this under >Menu >Base setting >Special functions >Int. switch on

In order to confirm this function, the system PIN "0000" must be entered, after which a check is placed behind the Int. switch on.

 

Function:

The setting "internal switch on" is actually used for conferencing within the base station (up to 6 headsets) With this function, a second user is given the option to participate in a conference with just one touch of a button.

This special function operates with the GN9120DB as well! However, I can now only dial a number with the cell phone. While the DECT telephone is dialling, press the multifunction button on the headset once and you will have the dial tone automatically in the GN9120DG.

{gnresource:HSS_GN9120-Funkaufbau-ohneBasis-WG}

Now put down the cell phone and you can make your call with the headset.

If this call is not for you (e.g. in a doctors practice) or you need to transfer it to someone else, then you can connect it back to the DECT telephone from the headset. To do this you need only press the "anwer the call" button on your mobile unit {gnresource:HSS_Siemens-SL1-Annahme-Taste-WG} and you have the call back to the SL1, for example. End the call by pressing the multifunction button on the headset.

Of course you can also use the DECT telephone's conference function with the GN9120DG and you have the ability to to hold a conference in up to 5 headsets and one cordless phone.

Manufacturer	Telephone
SIEMENS	Gigaset A140/A240/A340
SIEMENS	Gigaset A345
SIEMENS	Gigaset C340/C345
SIEMENS	Gigaset C450/C455
SIEMENS	Gigaset E450/E455
SIEMENS	Gigaset S100/S150
SIEMENS	Gigaset SL100/SL150
SIEMENS	Gigaset S440/S445
SIEMENS	Gigaset S450/455
SIEMENS	Gigaset SL550/SL555
TELEKOM	T-Sinus 710A/710K
TELEKOM	T-Sinus 711K/711 A Komfort
TELEKOM	T-Sinus 712/712K
TELEKOM	T-Sinus 712 A Komfort

Requirements:

GN 9120 EHS

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}

Art.-Nr. 9120-xx-11

{gnresource:HSS_Auerswald-Logo}


{gnresource:HSS_auerswald_COMfortel_2500_schwarz(1)(1)}

COMfortel 2500


Connection:

1.) Plug one end of the DHSG-cable marked in blue into the jack marked "head set icon" of the COMfortel 2500..

2.) Plug the split end of the DHSG-cable as follows into the base station of GN 9120. The RJ10 connector into the jack with the "Telephone icon" and the RJ45 connector into the jack marked "AUX" on the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}


Software setting:

The GN 9120 must be set on the DHSG software.
(The GN 9120 DHSG is always supplied in the DHSG mode)

To check this, you can set it as follows:
Plug the headset into the base station.

Then press the PLUS and MINUS keys simultaneously for 6 seconds till the online-indicator begins to flash on the headset.

Now your actual software is shown to you.
The radio lamp is for RHL"; the MUTE-lamp is for "DHSG" the accu-indicator is for "AEI".

Now you can switch between the individual software types with the PLUS or MINUS keys.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}
To confirm the set software, the device automatically switches
to the charge status agian after around 10 seconds.


Base setting:

{gnresource:HSS_9120_basis_einstellung_klein}

The adjustment knob on the base station must be set to A"


Setting the transmission volume:

Try making a call to someone with the headset.

Now press the PLUS and MINUS keys on the headset simultaneously, immediately thereafter you will hear a signal tone immediately.

Now you can increase the volume in the microphone with PLUS or decrease it with MINUS.

{gnresource:HSS_GN9120-�bertragungslautst?rkeeinstellen-WG}

As confirmation you will hear a gentle signal tone in the background after 15 seconds. Then all settings will be stored automatically.


Setting telephone:

Menu > Functions > Headset > ON

Menu > Setting > Base setting > Headset-type > DHSG-headset (confirm)

For a ring tone signal in the headset, you must undertake the following settings:

Menu > Setting > Signalling > Ringing in the headset (confirm)

Prerequisite:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}

9120-xx-11

{gnresource:HSS_Tiptel_Logo}


{gnresource:HSS_Tiptel85}

Tiptel 85

Connection:

1) Plug the 1-sided end of the DHSG cable that is marked in blue into the socket of your telephone that is marked with the "headset symbol"

2)Plug the split end of the DHSG cable into the basestation of the GN 9350. The RJ10 plug is plugged into the socket with the complete "Telephone symbol" and the RJ45 plug is plugged into the socket marked as "AUX" at the GN 9350 basestation.

Software setting:

The GN 9120 must be set with DHSG Software.
(the GN 9120 DHSG is always supplied in DHSG Mode)

Checking and setting can be carried out as follows:
Plug the headset into the basestation.

Then press both the PLUS and MINUS button simultaneously for 6 seconds until the online display on the headset starts to flash.

Now your current software is displayed on the basestation.

The radio lamp displays"RHL"; the MUTE-Lamp "DHSG" the Accumulator display represents "AEI".

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-Farblich-WG}

With the help of the PLUS or MINUS button you can toggle between particular kinds of software.
Installation of the software is confirmed when after about 10 sec the device again automatically changes over to the charge condition



Base setting:

The adapter (small wheel) on the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the transmission volume:


Now both the PLUS and MINUS button on the headset must be simultaneously pressed and immediately a beep is heard.

Now you can increase the volume of the microphone with the aid of PLUS button or decrease it with the aid of MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a slight beep heard after about 10 seconds. All the settings are subsequently automatically saved.

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111

{gnresource:HSS_logo}

{gnresource:HSS_innovaphone_IP230_klein}

Innovaphone IP 230

Connection:

1) Plug the 1-sided end of the DHSG cable marked in blue into the socket of the Innovaphone IP 320 marked with the  " Headsetsymbol " .

2) Plug the split end of the DHSG cable into the base station of GN 9120. Plug the RJ10 plug into the socket with the complete "Telephone symbol" and the RJ45 plug into the socket marked with "AUX" at the GN 9120 basestation.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set for DHSG Software .
( the GN 9120 DHSG is always supplied in DHSG Mode)

For control, checking and setting can be carried out as follows:

Plug the headset into the basestation.

Then press the PLUS and MINUS button for about 6 seconds until the online display
on the headset starts to flash.

Now your current software is displayed on the basestation.

The radio lamp displays RHL; the Mute-Lampe DHSG and the accumulator display displays AEI.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

With the aid of Plus or Minus button you can toggle between particular kinds of software.

Installation of the software is confirmed when the device once again automatically changes over to the
charge condition after about 10 seconds.

Base installation:

The adapter (small wheel) at the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Adjustment of the volume of microphone:

With the headset please make a call. If your interlocutor is unable to understand you or finds it difficult to understand, both the PLUS and MINUS button must be pressed simultaneously and immediately a beep is heard.

Now by using the PLUS button you can increase the volume of the microphone or alternatively decrease it by using the MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}
It is confirmed by a mild beep heard in the background after about 10 seconds. Subsequently the settings are automatically saved.

Prerequisite:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}

9120-xx-11

{gnresource:HSS_Siemens-Schrift-Bild-WG}

{gnresource:HSS_openstage40}

OpenStage 40 / 60 / 80

Connection:

1.) Plug the 1-sided end of the DHSG cable that is marked in blue into the socket of your OpenStage instrument marked with the " Headset symbol " .

2)Plug the split end of the DHSG cable into the basestation of GN 9120 as follows. The RJ10 plug is plugged into the socket with the complete " Telephone symbol " and RJ45 is plugged into the socket marked as " AUX " at the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

 The GN 9120 must be set for DHSG software.
(the GN 9120 DHSG is always supplied in DHSG mode)

For control, checking and setting can be carried out as follows :
Plug the headset into the basestation.

Then press the PLUS and MINUS button simultaneously for about 6 seconds until the online display on the headset starts to flash.

The basestation displays your current software.

The radio lamp displays "RHL"; the MUTE-lamp displays"DHSG" and the accumulator display displays "AEI".
With the aid of the PLUS or MINUS button you can toggle between different kinds of software.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

Installation of the software is confirmed when the device once again automatically changes over to the charge condition after about 10 seconds

Basic setting:

{gnresource:HSS_9120_basis_einstellung_klein}

The adapter on the basestation must be positioned to "A".

Adjustment of the transmission volume:

please make a call with the headset.

Now the PLUS and MINUS button on the headset must be pressed simultaneously and this immediately results in a beep. Now the microphone volume can be increased using the PLUS button or alternatively it can be decreased using the MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a slight beep heard after about 10 seconds. The settings are subsequently automatically saved.

Important:: The dial tone signal in the headset is transmitted only when standard ringtones are used on your telephone. No "call signalling" for mp3-ringtones

Your telephone may not be fully immune to the radio transmission between your headset and base. To
overcome this problem, move the base at least 30 cm/12” away from the phone. If you have a European
version, you can instead choose to set the headset to Low Power mode.

GAP (Generic Access Profile)

The GAP standard is supported by most modern DECT systems and is used to register external mobile devices. If you do not know whether your DECT telephone complies with this standard, you can look it up in the manual supplied with your telephone.

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111


{gnresource:HSS_Auerswald-Logo}


{gnresource:HSS_auerswald_COMfortel_2500_schwarz(1)(1)}

COMfortel 2500

Connection:

1.) Plug the 1-sided end of the DHSG-cable marked in blue into the socket of COMfotel 2500 marked with the " Headset symbol "

2) Plug the split end of the DHSG cable into the basestation of GN 9120.as follows: The RJ10 plug is plugged into the socket with the complete " Telephone symbol " and RJ45 is plugged into the socket marked with " AUX " at the GN 9120 basestation.

{gnresource:HSS_9120EHS_DHSG}


Software setting:

 The GN 9120 must be set for DHSG Software
(the GN 9120 DHSG is always supplied in DHSG Mode)

For control, Checking and setting can be carried out as follows:
Plug the headset into the basestation.

Then press the PLUS and MINUS button simultaneously for 6 seconds until the online display on the headset starts to flash.

Now your current software is displayed at the base.
 
The radio lamp displays "RHL"; the MUTE-LampDHSG" and the accumulator display represents "AEI".

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}
With the help of PLUS or MINUS button now you can toggle between different kinds of software.

Installation of the software is confirmed when the device once again automatically changes over to the
charge condition after about 10 secs.

Base installation:

The adapter on the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}


Adjustment of the transmission volume:

please make a call with the headset.

Now you must press the PLUS and MINUS button on the headset simultaneously and immediately after this a beep is heard.

Now you can increase the volume by using the PLUS button or alternatively decrease it by using the MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

This is confirmed by a slight beep after about 10 seconds. The settings are subsequently automatically saved.


Telephone setting:

Menu > Functions > Headset > ON

Menu > Setting > Basic setting > Headset-Type >DHSG-Headset (Confirm)

The following setting must be made for indicating a dial tone in the headset:

Menu > Setting > Signalling > Headset-ringing ( Confirm )

Prerequisite:

{gnresource:HSS_GN9120_DUO}

GN 9129-808-111

{gnresource:HSS_Auerswald-Logo}

{gnresource:HSS_auerswald_COMfortel_2500_schwarz(1)(1)}

COMfortel 2500


Connection:

1) Plug the 1-sided end of the DHSG-cable marked in blue into the socket of Auerswald COMfortel 2500 marked with
the " Headset symbol " 

2) Plug the split end of the DHSG cable into the basestation of GN 9120.
The RJ10 plug is plugged into the socket with the complete " telephone symbol " and the RJ45 is plugged into the socket marked as " AUX " at the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}
Software setting:

 The GN 9120 must be set for DHSG Software .
(the GN 9120 DHSG is always supplied in DHSG Mode)

For control, Checking and setting can be carried out as follows:
Plug the headset into the basestation.

Then press the PLUS and MINUS button simultaneously for 6 seconds until the Online display on the headset starts to flash.

Now the current software is displayed on the basestation.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

The radio lamp represents "RHL"; the MUTE-Lamp"DHSG" and the accumulator display represents "AEI".

With the aid of the PLUS or MINUS button you can toggle between different kinds of software.

Installation of the software is confirmed when the device automatically once again changes over to the
charge condition after about 10 secs.


Base setting:

The adapter (small wheel) on the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}


Adjustment of the transmission volume:

Please make a call using the headset.

Now you must press the PLUS and MINUS button on the headset simultaneously, immediately after which a beep is heard.

Now you can increase the volume with the aid of the PLUS button or alternatively decrease it with the aid of MINUS button.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

As confirmation a slight beep is heard after about 10 seconds. Subsequently the settings are automatically saved.


Telephone setting:

Menu > Functions > Headset > ON

Menu > Setting > Basic setting > Headset-Type >DHSG-Headset (Confirm)

The following setting must be made for a dial tone signal in the headset:

Menu > Setting > Signalling > Headset-ring   ( Confirm )

Requirements:

{gnresource:HSS_GN9120-Bild-WG}    +         {gnresource:HSS_Akustikadapter-Bild-WG}

    GN 9120 EHS               Acoustic-Adapter ( min. version 10 )

{gnresource:HSS_SwyxLogo_klein}
{gnresource:HSS_SwyxPhoneL440}
L420 e / L420 s / L440 / L520 /  L540

Equipment:

starting at SwyxWare 5.1

Important: If any of the components are missing, then the electronic call acceptance function will not work!


Connection:

Please use the blue labeled( DHSG ) connection cable.

1) Insert the 1-sided blue end of the DHSG cable in the OptiPoint Acoustic Adapter plug socket labeled " Headset symbol ".

2) Insert the split end of the DHSG cable into the GN 9120 base station and insert the RJ10 jack in the plug socket with the complete" Telephone symbol " and the RJ45 jack in the plug socket labeled " AUX " on the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}

Software settings:

GN 9120 has to be set on the DHSG software.
(the GN 9120 DHSG is always delivered in DHSG mode)

It can be controlled and/or set as follows:
Place the headset on the base station.

Then press the PLUS and MINUS buttons simultaneously for 6 seconds until the on online display on the headset begins to blink.

Then the current software is displayed on the base.
The wireless light represents RHL; the MUTE light represents DHSG and the recharging display represents AEI.

You can now switch between each software with the PLUS or MINUS button.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}
To confirm the software setting, the device automatically switches to recharge again after 10 seconds.


Setting the base:

The adjustment control (small wheel) on the base station has to be set to "A".

{gnresource:HSS_GN9120-EinstellungRad-WG}


Setting the transmission volume:

Please call someone with the headset on.

Now, press the PLUS and MINUS button on the headset simultaneously, then a signal tone will immediately sound.

Now, the microphone volume can be increased by pressing PLUS or lowered by pressing MINUS.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}
After 10 seconds, a signal tone can be heard in the background indicating confirmation. The settings are then automatically saved.


Settings on the telephone:

Important! As soon as the headset is connected and set, the telephone has to be reset so that the EHS function is assumed.

Optionally, a headset can be set-up via the telephone menu ( *91 >Select key>Next>Headset ).

Requirements:

Jabra GN9120 Standard

Art.no.: 9120-xx-01{gnresource:HSS_GN9120-Bild-WG}

Jabra GN sound card cable 8800-00-29

{gnresource:HSS_8800-00-29-WG}

 

Connection:

1. Insert the 4-pin RJ10 modular connector into the socket on the Jabra GN9120 base station labeled with a telephone symbol.

{gnresource:HSS_GN9120BasisQuer-WG} (internal socket/telephone symbol)

2. Insert the phone jack into the respective sound card socket on your PC.

 

Setting the audio and playback volume on a desktop PC or laptop:

The audio and playback volume should be set to halfway in your system settings under Sounds and Audio Device when connecting the Jabra GN9120 via a sound card cable.

{gnresource:HSS_VolumeControl-USB-Klein-WG}

 

Setting the transmission volume on the Jabra GN9120:

Please call someone with the headset on.

Now press the PLUS and MINUS button on the headset simultaneously, a signal tone will then sound.

You can now increase the microphone volume by pressing PLUS or lower it by pressing MINUS.

After 15 seconds, a faint signal tone can be heard in the background confirming the change. The settings are then automatically saved.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

  

Adjustment on the Jabra GN9120 base station:

The adjustment control (small wheel) on the base station must be set to "A".

{gnresource:HSS_GN9120-EinstellungRad-WG}

Now press the PLUS and MINUS button on the headset simultaneously, a signal tone will then sound.

You can now increase the microphone volume by pressing PLUS or lower it by pressing MINUS.

After 15 seconds, a faint signal tone can be heard in the background confirming the change. The settings are then automatically saved.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

  

 

 

 

 

 

Prerequisite:

{gnresource:HSS_GN9120_DUO}  +   {gnresource:HSS_Akustikadapter-Bild-WG}

GN 9129-808-111     Adapter-Universal ( min. version 10 )

{gnresource:HSS_logo_t_com}

{gnresource:HSS_ComfortPro_P100_Klein}

Comfort Open P 100 / 300 IP

System:

Comfort Open

Connection:

1.) Plug in the 1-sided end of the DHSG cable marked in blue into the socket of the universal adapter that is marked with the
" Headset symbol " .

2.) Plug the split end of the DHSG cable into the basestation of the GN 9120. The RJ10 plug is plugged into the socket with the complete " Telephone symbol " and RJ45 into the socket marked witht " AUX "at the GN 9120 base station.

{gnresource:HSS_9120EHS_DHSG}

Software setting:

The GN 9120 must be set for DHSG Software
( The GN 9120 EHS is always supplied in DHSG Mode.)

For control, checking and setting can be carried out as follows:

Plug the headset into the basestation and press the PLUSaund MINUS button
simultaneously for about 6 seconds until the online dispaly on the headset starts to flash.

Now your current software is displayed at the base station.

The radio lamp displays RHL; the MUTE-LED DHSG and the accumulator display AEI.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}

With the help of PLUS and MINUS button now you can toggle between different kinds of software.
Installation of the software is confirmed when the basestation once again automatically changes over to the charge condition after about 10 seconds.

Base installation:

Set the telephone setup switch ( A-G ) at the position "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Transmission volume adjustment:

With the headset please make a call.

Now both the PLUS and MINUS button on the headset must be simultaneously pressed and immediately a beep is heard.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}
Now the volume of the microphone can be increased by using the PLUS button or alternatively it can be decreased by using the MINUS button.

This is confirmed by a slight beep in the headset after about 5 seconds. The settings are subsequently automatically saved.

Telephone installation:

Additionally a Headset button must be installed on the Comfort Open .

Important:: As soon as the headset is connected and adjusted, the telephone must be reset to adopt the EHS function .

For the electronic call acceptance function the Jabra GN9120 EHS can be connected to the following devices/equipment:

 

MANUFACTURER	Requirements	EHS mode 9120
Aastra	Aastra office 70IP / 80IP	DHSG
AGFEO	ST30 + HS30 module	DHSG
AGFEO	ST31	DHSG
AGFEO	ST40	DHSG
AUERSWALD	Comfort 1000-2000	RHL + AEH-02 module (Receivable at GN)
AUERSWALD	COMfortel 2500	DHSG
DeTeWe	Open phone 63/65 + AZ adapter + OpenCom device 100 from release 5.2 Open Com device 1000 from release 3.2	RHL + DE-EHS-001 (Receivable at GN)
DeTeWe	Open phone 71/73/75 including IP	DHSG
ELMEG	CS 410	DHSG
ELMEG	CS 290-U / CS 410-U	DHSG
INNOVA PHONE	IP 230	DHSG
MEDIASTREAMS	e-phone	RHL + COM1 cable RS232 (must be ordered with the Softphone!)
Nortel network	M3310/M3820	RHL
SIEMENS	OptiPoint 500/600 + OptiPoint acoustic adapter + HiPath 4000 from version 1 HiPath 3000 from version 3 SMR 14 HiPath 3000 from version 3 SMR 7 HiPath 2000 from version 1 HiPath 1220 from version 2.1 build032 HiPath 500 from version 5	DHSG
SIEMENS	OptiPoint IP 410/420 + OptiPoint acoustic adapter + HiPath 4000 from version 1 HiPath 3000 from version 3 SMR 14 HiPath 3000 from version 3 SMR 7 HiPath 2000 from version 1 HiPath 1220 from version 2.1 build032 HiPath 500 from version 5	DHSG
SIEMENS	OPENSTAGE 40 - 80	DHSG
SWYX	L420/L450 + Acoustic adapter (min. version 10 ) From SwyxWare 5.1	DHSG
SWYX	Swyxlt + From SwyxWare 5.1	RHL + COM1 cable RS232 (must be ordered with the Softphone!)
T-COM	Octophone F20/30/40/50 + Universal adapter + Octopus open F200-900	DHSG
T-COM	Octophone IP 30 + Universal adapter + Octopus open F200-900	DHSG
T-COM	T-comfort 730/830 + T-comfort 930 DSL	RHL + DE-EHS-001 (Receivable at GN)
T-COM	Netphone	RHL + COM1 cable RS232 (must be ordered with the Softphone!)
T-COM	T-comfort open P 100 /300 IP + universal adapter + octopus open F200-900	DHSG
T-COM	T-comfort pro P 100/300/500 + octpus open F200-900	DHSG
T-COM	Comfort pro P 300/ 500 IP + octopus open F200-900	DHSG
T-COM	Octophone F640 / F660 / F 680	DHSG
TENOVIS	TM13/TH13 + Integral 3/5 Integral 33/55	AEI
TENOVIS	T3/T3 IP + Integral 3/5 Integral 33/55	AEI
TIPTEL	Tiptel 85 Tiptel 275	DHSG

For details on connection, please see the EHS-instructions for product GN 9120 EHS!

• Check that all the cords and plugs are connected correctly
• Check that the power adapter is plugged in and has power
• Check that the on-line indicator is lit. If it is not, place the headset in the base unit and take it out again
• Check that the battery is charged. If the battery is fully charged, the battery charging indicator on the
base unit will light when the headset is placed correctly in the base unit.

Telephone connection:

1. Disconnect the hand instrument cable from the telephone and connect it to the socket marked with hand instrument onthe basestation

2. Connect the connection cable of the socket of the hand instrument to the underside of your telephone.

3. Plug the power supply into the basestation and connect it to the power.

4.Place the basestation in the pedestal and rotate until it is firm.

5. Insert the headset into the basestation to charge the headset accumulator

{gnresource:HSS_Anschluss_9120Duo_2}

Ensure that the Telephone Termination Switch is in the correct position and that you have adjusted the
Transmit Power. Please refer to the relevant section in the reference guide.

Requirements:

GN 9120 MSH

Art.Nr.: 9120-x81-11 {gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein)

{gnresource:HSS_Alcatel_logo_klein}or {gnresource:HSS_t-com_logo_150}

    Touch 4029                      Open Phone 141

   Touch 4039                      Open Phone 151

 

Connection:

Connect GN 9120 MSH to the provided EHS cable connection:

{gnresource:HSS_9120_basis__ehook_anschluss}2-western socket (RJ10 +RJ45)

2-sided end: Plug the RJ45 into the jack marked "AUX" and RJ10 into the jack marked "telephone icon" on the base station.

2-fold Y-coupling end: Plug the 3.5 mm phone connector into the headset jack and the RJ12 into the "ringing jack" of the device. Now plug the telephone wire directly into the additional slide-on receptacle of the Y-cable.

{gnresource:HSS_alcatel_ehook_telefon_ip_klein}

 

Base setting:

{gnresource:HSS_9120_basis_einstellung_klein}

The settings knob on the base station must be set at "A".

 

Setting transmission volume::

Now try calling someone with the headset.

Now you mut press the PLUS and MINUS keys at the headset simultaneously, immediately thereafter you will hear a signal tone.

{gnresource:HSS_GN9120-�bertragungslautstärkeeinstellen-WG}

Now you can increase the volume in the microphone with PLUS or decrease it with MINUS. As confirmation you will hear a gentle signal tone the background after 15 seconds. Then the settings will be stored automatically.

Important: A ring tone signal in the headset will then only be transferred if

the "Standard/Nature" ring tone signaling has been set on your telephone.

Setting:

Menu > Setting > ringing tone > tune > standard or nature

Setting telephone:

Menu > Setting > telephone > ringing connector or jack > Microphone receiver set

A conference circuit on the GN9120 needs a GN9120-xx-01/11 and at least one more headset (maximum 4 headsets simultaneously on one station). These can also be ordered individually with a separate charging station. (Single headset: 91xx-01 // Charging station: 9160-01)

+  +

Remove the headset from the base station and place a call.

This headset is now the "Master headset" and controls the conference.

Now place the second headset in the base station during the call. All signal lights are displayed on the base for approx. 5 seconds. Afterwards the recharging display will blink for the duration of the charging, and the wireless symbol for as long as the master headset connection remains established.

  (The red "mute" light goes out after approx. 5 sec)

After this process, remove the second headset from the station. A simple signal tone can be heard in the headset and this is acknowledged by pressing the multifunction button once.

 (press once)

The second headset is now in the conference. The second participant can now leave the conference by pressing the multifunction button once or the master headset can completely end the conference by pressing the multifunction button once.

If a second headset from an existing station was used, then this headset is automatically connected back to its original base station when the conference ends.

TIP:

This switching to conference can take place even without a telepone or PC, as what is known as the "Walkie Talkie function." This is how the GN9120 enables a conference of up to 4 participants within a 150 m range; however, the connection to the master headset must be maintained, because if this ends the connection, then they will all need to be re-established.

 

When the battery is removed or the power adapter is unplugged (for at least a few seconds), all
customised headset settings are returned to factory-set default settings.

GN 9120 standard or E-Hook

Prerequisite:

{gnresource:HSS_9120-48-01KomplettWebSHop72dpiklein}+     {gnresource:HSS_EHS-AV-001II}

 9120-xx-11             EHS-AV-001


{gnresource:HSS_Avaya_Logo}

{gnresource:HSS_Avaya2420}

Avaya 2420 Version " B "

Callmanager Software 4.0

Connection:

1)Disconnect the network cable of your telephone.

2) Connect the EHS adapter to the " EU24/ ADJ " socket of your Avaya instrument and the   
" AUX " interface of your GN 9120 basestation.

3) Plug the 4-pin connection cable (RJ10 to RJ10) into the socket marked with a "Telephone symbol" on the basestation of GN 9120 and the opposite side into the "Headset interface" of your telephone.

4) Now you can reconnect the network cable to the telephone.

Software setting:

The GN 9120 must be set for DHSG software .
(the GN 9120 DHSG is always supplied in DHSG mode)

For control, checking and setting can be carried out as follows:

Plug the headset into the basestation.
Then press the PLUS and MINUS button simultaneously for about 6 seconds until the online display on the headset starts to flash.

Now your current software is displayed on the basestation.

{gnresource:HSS_DHSG-AEI-RHL-Umschaltung-WG}
The radio lamp displays RHL; the Mute-Lamp DHSG and the accumulator display displays AEI. with the aid of PLUS or MINUS buttons you can alternate between individual software types.

For the confirmation of sofware installation the headset automatically changes over to the charge condition after about 10 seconds.

Base setting:

The adapter (small wheel) on the basestation must be positioned at "A".

{gnresource:HSS_9120_basis_einstellung_klein}

Transmission volume adjustment:

Please make a call using the headset.

Now both the PLUS and MINUS button on the headset must be pressed simultaneously and this immediately results in a beep.

{gnresource:HSS_GN9120-�bertragungslautst�rkeeinstellen-WG}

Wiith the aid of the PLUS button the volume can be increased or with the aid of MINUS button it can be decreased. For confirmation, a slight beep is heard in the background in the headset after about 10 seconds. The settings are subsequently saved.